Gardening – My Favorite Homemade Tool

Gardening can be a very personal endeavor. There are some who love the joy and satisfaction of growing vegetables in our desert environment. There are others who focus on ornamentals and the beauty of flowering cacti. Most gardeners not only focus on particular plants, but over the years, they collect a bevy of favorite gardening tools.

This is one of my favorite gardening tools and time savers.



Wherever I have gardened, one of the first things I have done was build a dirt sifter. I use it many times each season. Perhaps my workflow differs from yours so let me explain…

Our agave collection, for example, gifts us with pups and after they are potted up and cared for a while, they grow their own set of “offspring” and need to be separated and shared.



The rootball is often dense and needs to be dismantled.



We first separate as many of the viable plants and roots as possible for replanting and/or sharing.



The next step is to place the densest part of the root ball on top of the sifter, break it up with a trowel and then rub it back and forth so the soil is released in to a garden cart or cement mixing bin (which we use to mix soil).





In the end we are left with a yield of reusable soil mix. The old roots and debris are discarded. More about the soil mix in a bit.



If the soil is wet or damp, it is placed on the side of our house where the afternoon sun warms and dries it.



Once the soil is dry, we place it in a large covered trash can to be used in our planting medium for new plants. Once again, if you speak to a dozen gardeners, you will probably get thirteen recipes for various plant mixes. This is a very individual preference, but since you ask, here is one I use for non-succulent plants.

Planting Mix
– A five gallon bucket is used as the basic unit –

  • 1/3 – old plant mix that has been sifted
  • 2/3 – new plant mix – I use the Natural & Organic Potting Soil purchased from Summer Winds Nurseries.
  • 2/3 – of a large coffee can of gravel 1/4″ +/- which I purchase in bulk from MDI (2815 E. RoseGarden LN, Phoenix , AZ 85050). This increases drainage and provides a small buffer against over watering. *Adjust as necessary
  • 1 – Large coffee can of used coffee grounds (when available).
  • Mix all the ingredients very well until it appears even in texture and color. Don’t stint on this step. I use a large cement mixing bin and a standard shovel or in the large garden cart.
  • For flowering plants I use a dose of super bloom fertilizer following the recommended amount on the container UNLESS experience has dictated otherwise. This is added after the plant is potted and just before watering-in.





Let’s talk about the sifter. We are not building a piece of furniture here so it doesn’t have to be pretty or perfect. Good enough will be just fine for this project.

As you can see, the frame is made from simple 2 x 4’s. One will probably do, but decide how large you want it. Place the pieces of the frame on a flat surface and use L-brackets to fasten the sides.

NOTE – Our sifter is 35″ by 20″ after assembly and accounting for the width of the wood. The sifting surface is relatively smaller. Just decide how large you want it and purchase the appropriate amount of wood.



I then take one longer screw and screw it into each corner of the frame. Drill a pilot hole to assure alignment and to help keep the wood from splitting.



I purchased a roll of 1/2″ hardware cloth that we use for several different gardening tasks and cut it so there was an overlap around all of the sides of the frame. Be careful to trim off any pieces that stick out beyond the grid or you will be creating needles that will puncture gloves and fingers alike.



I then secured the hardware cloth using 3/4″ hot dipped, galvanized poultry net staples. Tap them in as far as they will go. It is OK if they stick out a bit as long as they don’t snag debris, gloves, etc. If you prefer, just hammer them flat so they don’t stick out as much.



Use a wire snip to cut the corners and fold them over similar to wrapping a present and secure the corners well with the staples mentioned above.



NOTE – In one iteration of building a sifter, I erroneously thought that if one layer of hardware cloth was good, two would be better so I assembled the frame using two layers of hardware cloth. That was a big mistake because debris was caught between the two layers. One layer is more than sufficient.



Of course, the sifter isn’t used only for breaking root balls, it is also great for sifting native soil and/or removing large rocks from a pile of dirt. It can even be turned upside down and used to protect seeds from birds or small rodents. Just be sure to place rocks on each corner so the rabbits and squirrels have less of a chance of moving the barrier.



NOTE – This procedure would be the same no matter where you garden. The only modification you would need to make would be in the planting mix and I am sure that you probably have your own favorite variation.

If you have any questions, leave them in the comment section and I will answer to the best of my ability.

 

Read more gardening posts HERE


**********


All original content on this blog is copyrighted by Jeffrey B. Ross with ALL Rights Reserved. While reference links back to JBRish.com are appreciated and encouraged, please acquire approval for any reproduction of original content from this website.

©Jeffrey B. Ross 2014 – 2019 – JBRish.com



Mum is the Word in the Desert Garden

Prior to moving to the Valley of the Sun, north of Phoenix, Arizona, we lived in northwestern New Jersey; Hunterdon County. We normally gardened from May through October and there were times when we started seeds indoor in early April. We could stretch our gardening into the fall and early winter by including Chrysanthemums.

Mums were part of the Halloween-Thanksgiving trimmings in our area. We usually had them placed on our front steps often with thin netting over them to keep the deer from nibbling. There were years when we were able to winter over a mum or two, but much of the time our efforts fell short or the variety we purchased was not as hardy as we thought.



We were surprised to find that mums are available for purchase in our area of Arizona during the same season as in the northeast. It was only natural then that we began to fold some of them into our Halloween-Thanksgiving floral displays.

Because our experience with Chrysanthemums was anchored in the northeast, we figured that once the real hot weather of sustained ninety to one-hundred and above came along, that these familiar plants would wither and die.

Imagine our surprise to find that they, given enough shade and water, fight off the heat to usher forth extended blooms during the late spring and summer and into the following fall. To give these plants the best chance possible for surviving in this less than hospitable climate, we have a routine we follow in the early spring.

This is the mum we selected for what we call revitalizing.



As readers can see, the green leaves make up only about one-half to two-thirds of the plant and there are a lot of brown, dead leaves and stems.



What we normally do if it is warm and the sun is in full flare is bring the plant into the shade of one of the garage bays and work there. We move the plant into the garage and remove the rock mulch that we use in almost every planter.



Once the rock mulch is removed, much of the dead parts of the plant are trimmed.



After the initial trimming, we begin to excavate the root ball.



NOTE – Notice that we work mostly on a drop cloth to catch errant dirt, stones and debris. The old dirt is offloaded to a cement mixing bin to dry and save for use in a future rejuvenated mix.

Once the root ball is excavated, it is examined to make sure the roots are white and in good condition and there are no grubs hiding. Then I gently remove more of the dead, hard stems and any dead roots.

NOTE – Be careful to leave most of the rootball intact as the plant will need to recover even from a mild root trimming and tickling.



Here is a closer look:



There are some stems so low to the base of the root ball that they have to be cut away with a scissors or garden shear which reduces the chance of disturbing too much of the root ball.



I make one final inspection of the root ball and very gently loosen some of the compacted roots so they are able to spread when they grow anew.



On the left is the old pot with the remaining old dirt. In the upper middle area of the picture is the new, smaller pot that is lighter in color. The new plant will spend much of the summer in this pot, but may need to be transplanted in to a larger pot later.



Enough new planting mix is placed in the pot to take up approximately one third. This is the bottom third of the planter.



To encourage downward root growth, I place a small amount of fertilizer in the bottom of the pot (notice the green dots in the ovals- BELOW) and then mix them into the top part of the bottom mix. The green dots are hard to discern in this photo and may be confused with gravel which is used in the planting mix. The arrows show the gravel which is much less uniform in shape.



The new planter is placed inside a bin to catch any stray dirt. Dirt is added to the correct depth to bring the crown of the plant to about three-quarters of an inch below the rim of the pot. I usually create a cone in the center and put the newly trimmed rootball in the center. The dirt is then filled in around the rootball as shown above.



Here is the plant with the dirt filled in and new, different fertilizer added (see the Vigoro in the background).



After the planting is complete, water is gently added. I use my hand to break the flow and spread the water around the rootball of the plant. Once the plant has been watered so that water runs freely through the bottom of the pot, I gently press the dirt down to remove any potential air pockets.

NOTE – Don’t press down too hard which may compact the roots; just gently.



Now it is time to move the plant to its place in the courtyard. We picked an area that will receive mostly shade with a bit of sun during the day. This will protect the mum from the blazing heat. Notice that a two gallon per-hour emitter (red) has been anchored to the side of the plant.



Another emitter is added to the other side of the plant to provide even coverage when watered.



We place the rock mulch on top of the plant, which also helps to hold the emitters in place and give one final watering. A protective cover is placed over the pot for a couple of days to provide bit of shade. The Dollar Store or Target sells laundry baskets, crates, etc. that serve this purpose. Sometimes we need to drill more holes depending on the configuration.

NOTE – We often put a weight on top of the “covers” to keep them from blowing off in the wind.



The plant is carefully checked over the next couple of days and after that, the basket or crate used to shield the sun is removed. The plant then needs time to grow and in a few months this is how it looks.



You can see it here (BELOW) on the left. As the summer progresses, the snail vine will grow to cover the sun trellis and offer enough shade to provide an appropriate environment for the plant during the hottest summer days.



You may also note two other mums on the right that we transplanted in the same fashion .



We have followed this procedure for a couple of years now and it has served us well. I wouldn’t have guessed that we would be able to winter-over or perhaps more appropriately, summer-over the mums in our Sonoran Desert environment.

 

Read more gardening posts HERE


**********


All original content on this blog is copyrighted by Jeffrey B. Ross with ALL Rights Reserved. While reference links back to JBRish.com are appreciated and encouraged, please acquire approval for any reproduction of original content from this website.

©Jeffrey B. Ross – 2018 – JBRish.com